High Speed Door Servo Control System

Introduction

Thank you for choosing High Speed Door Servo Control System.

Please read this manual carefully before you start to use the system. In this manual you will find instructions for how to set the operating code the controlunit, malfunction diagnostics and debugging, and routine maintenance.

Notice: 

? Before connecting the system to live wire place make sure the power supplyis off.

? Please make sure the power voltage in the main circuit is the some ascontroller’s rated voltage. Also please make sure the ground terminal is properly and reliably connect to the ground wire.

? DO NOT touch output terminal directly. DO NOT shot circuit the outputterminal and out shell.

? After the power supply is cut, and before the LCD is off, there still highvoltage electricity in the circuit, so DO NOT touch the internal wiring and electronic components.

? ? Internal wiring and electronic components are very sensitivity to staticelectricity, so DO NOT let any object contact the internal wiring and electronic components of motor driver and the main circuit of the touch control panel.

Inspection

All product has passed inspection and testing before is leaving the factory.

When you open the unit place make sure there is no damager during shipping.

Also to confirm the equipment ratings are matching your requirement.

General Characteristic

Our servo control system is suitable for high speed PVC and aluminum doors.

The system is in compact package, with high torque and high operating speed,lower noise, high reliability, smooth and soft operating curves, it’s suitable for high speed and intensive usage environment.

The rolling curtain can be controlled by wall switch, push button, bluetooth, radar,safety edge, photo eye, induction loops, etc.

Operating Speed: 0.5m/s-1.5m/s; Operating Width: ＜16 ㎡/30 ㎡/60 ㎡; Daily operating time: 2000 time; Rated voltage: 220V; Rated Output: 0.75KW/1.5KW/2.2KW。

大致翻譯：

快速門伺服控制系統

介紹

感謝您選擇高速門伺服控制系統。

在開始使用系統之前，請仔細閱讀本手冊。在本手冊中，您將找到有關如何將操作代碼設置為控制單元，故障診斷和調試以及日常維護的說明。

注意： 

?在將系統連接到火線之前，請確保電源已關閉。

?請確保主電路中的電源電壓是控制器的額定電壓。另外，請確保接地端子正確可靠地連接到地線。

?請勿直接觸摸輸出端子。不要射擊輸出端子和外殼。

?切斷電源后，在LCD關閉之前，電路中仍然存在高壓電，因此請勿觸摸內部接線和電子元件。

?內部接線和電子元件對靜電非常敏感，因此請勿讓任何物體接觸電機驅動器的內部接線和電子元件以及觸摸控制面板的主電路。

檢查

所有產品在出廠前都已通過檢驗和測試。

打開設備時，請確保在運輸過程中沒有損壞者。

同時確認設備額定值符合您的要求。

一般特征

我們的伺服控制系統適用于高速PVC門和鋁門。

該系統采用緊湊型封裝，具有高扭矩，高運行速度，低噪音，高可靠性，平穩柔軟的操作曲線，適用于高速，密集的使用環境。

卷簾可以通過墻壁開關，按鈕，藍牙，雷達，安全邊緣，光眼，感應線圈等進行控制。

運行速度：0.5m / s-1.5m / s;經營寬度：<16㎡/30㎡/60㎡;每日操作時間：2000次;額定電壓：220V;額定輸出：0.75KW / 1.5KW / 2.2KW。